Leo · 2026-11
Yes, you can use a NAS for security cameras, provided three numbers line up before purchase: camera bitrate, retention days, and sustained disk throughput. A NAS records IP cameras through ONVIF or RTSP streams and writes them to shared storage, but it is not a drop-in replacement for a dedicated recorder unless those numbers are calculated first.

The question behind can you use a NAS for security cameras is usually a cost question. Buyers already own or plan to own a NAS for files, and adding cameras to the same box looks cheaper than a second appliance. Sometimes it is. The difference between a working setup and a frustrating one is arithmetic done before the first camera is mounted.
It receives the stream over the network and writes it to disk as a continuous recording, usually in a container the vendor’s surveillance module can index and play back.
Two protocols matter. ONVIF defines how the appliance discovers a camera and negotiates its stream settings, and RTSP carries the media itself. A camera that speaks both is straightforward; a camera that speaks only a vendor-proprietary protocol may still work through a generic RTSP URL, but discovery and multi-stream selection will need manual entry.
The appliance side needs a surveillance application that runs on the device, plus enough CPU headroom to demux several concurrent streams. Writing eight 4 Mbps streams is not a heavy disk load, but decoding them for motion detection is a compute load, and that is where under-specified hardware shows up as dropped frames rather than as an error message.
Bitrate per camera, retention days, and disk throughput. Capacity follows from the first two; the third decides whether playback stays usable while recording continues.
Use the standard storage formula: terabytes = cameras × bitrate in Mbps × 86,400 × retention days ÷ 8 ÷ 1,024 ÷ 1,024. The 86,400 is seconds per day and the 8 converts bits to bytes.
Consider a hypothetical eight-camera installation at 4 Mbps per camera with 30-day retention. Eight cameras × 4 Mbps = 32 Mbps aggregate. Then 32 × 86,400 = 2,764,800 megabits per day. Multiply by 30 days: 82,944,000 megabits. Divide by 8 for bytes: 10,368,000 megabytes, which is about 10.4 TB before filesystem overhead. On a two-drive array in RAID 1 that means two 12 TB drives; in a four-drive array it could be four 6 TB drives in RAID 5 for a similar usable figure after parity.
Now change one input. Move the cameras to 6 Mbps for better motion detail and the same 30 days needs about 15.6 TB. Drop retention to 14 days at 6 Mbps and it falls back to about 7.3 TB. Those two levers, bitrate and days, move the disk bill more than the camera count does.
A single 4 Mbps stream needs 0.5 MB/s, so eight of them need about 4 MB/s for recording. The load that matters is playback and export running at the same time.
Reviewing four streams at once while exporting a clip adds tens of megabytes per second of read activity, not megabytes per hour. Any modern SATA array handles that. The risk is not the array but the network: eight cameras at 4 Mbps is 32 Mbps aggregate, comfortable on 1GbE, but the same port also carries file traffic and backups. On a shared 1GbE link, a large file copy can starve the recording path long enough to drop frames, which is why surveillance traffic is usually kept on its own VLAN or its own port.
ONVIF for discovery and RTSP for transport, plus a decision on PoE power before the cable is pulled.
PoE cameras take power over the same Ethernet cable, which removes a power outlet per camera and is the reason most installers prefer it. The budget side is straightforward: a PoE switch or injector supplies a fixed wattage per port, and the camera’s published power draw has to fit inside it with margin for startup surge. If the appliance itself supplies PoE ports, confirm how many and at what per-port budget before planning the run, because a mixed load of cameras and access points will exceed a small budget quickly.
ONVIF profiles define which capabilities a camera exposes, and RFC 7826 documents the RTSP 2.0 protocol that carries the stream, both checked November 18, 2026. Ask a supplier which profile level the camera implements, because a camera that only supports a minimal profile may not expose motion events to the recorder.
It combines the recorder role with storage, and it does the detection on the device rather than in a cloud service.
The S1 from woCyber, an export brand of a Beijing-based storage hardware manufacturer, is a combined edge AI recorder and private cloud appliance. Its published description lists on-device person, vehicle, and pet classification with a false-alarm rate below 3 percent, PoE camera access over ONVIF, QR-code pairing with automatic discovery, retention options of 7, 14, and 30 days with event-triggered and continuous recording, and all computation on the device with per-account isolation. Disk bay count, CPU model, memory, network port specification, and maximum capacity are not published, so buyers should request them in writing. The products/s1-security-kit page carries the published specification.
That matters because cloud-tied camera systems charge per camera per month, and the bill grows with the installation rather than with the data. A local appliance moves the cost to hardware and drives, and keeps the footage on site, which is the property most buyers are actually shopping for.

| Aspect | NAS with surveillance app | Dedicated NVR | Cloud camera subscription |
|---|---|---|---|
| Cost structure | Hardware plus drives, one time | Hardware plus drives, one time | Per camera per month |
| File sharing | Native, same box | Limited or none | None |
| Camera choice | Broad if ONVIF and RTSP are supported | Often brand-restricted | Vendor-locked |
| Analytics location | On device, depends on app | On device | Vendor cloud |
| Setup effort | Higher: users, shares, app tuning | Low | Lowest |
The honest limitation is support surface. A NAS running a surveillance application has two vendors in the path, the appliance maker and the camera maker, and each may point at the other when a stream misbehaves. A single-brand recorder reduces that ambiguity at the cost of camera choice. Buyers who value camera flexibility should confirm the appliance vendor will help with third-party camera troubleshooting before signing.
One design decision deserves attention before purchase: whether the same appliance carries both file shares and camera recordings. Sharing a device keeps power and cabling simple and lets one backup policy cover everything, but the two workloads have different disk profiles. Camera recording writes continuously and sequentially; file access is bursty and random. At the camera counts discussed here the two coexist on a four-drive array without trouble, but the retention policy has to be set for the surveillance volume separately, because a cleanup script written for documents can delete recordings, and a recording loop can fill a volume that was meant for files. Separate volumes on one appliance, or two appliances, both solve it. The mistake is assuming one volume handles both.

Install one camera, record 24 hours, and replay it at speed on the device.
Check four things in that test. Confirm the stream appears without manual URL entry, which tells you discovery works. Confirm the timestamp on playback matches the camera clock. Pull the network cable for thirty seconds and confirm the recording resumes with a visible gap rather than silently stopping. Export a clip and open it on a machine that has none of the vendor software installed, which is the test that catches proprietary container formats.
Also measure the write rate during the test. A single stream is trivial, but the number that matters is headroom for the eighth camera, and a device that struggles with one stream will not improve at eight.
Protocol support, PoE budget, retention, restore procedure, and the list of what is not published.
Write down the camera count, the bitrate per camera, the retention days, and the resulting capacity. Then add the appliance requirements: ONVIF support stated as a capability rather than a certification, PoE port count and per-port budget, snapshot or export behavior, and the account model for whoever reviews footage. Buyers comparing a NAS against a dedicated recorder can work through the nvr-vs-nas-for-surveillance-which-appliance-fits-your-cameras comparison and the onvif-camera-compatibility-an-integrator-checklist compatibility checks first.
woCyber builds OEM and ODM storage hardware with research and development in Beijing and mass-production manufacturing in Shenzhen, publishes CE, UKCA, FCC, RoHS, REACH, and WEEE documentation for its product lines, and ships from 100 units per SKU for reconfiguration projects. Integrators planning a multi-site rollout should also size the power budget with the poe-camera-power-budget-planning method before ordering switches.
The last item on the list is the one that gets skipped: write down what the vendor would not confirm. A gap in writing today is a support argument in month six.

S1 combines an edge AI NVR and private-cloud NAS in one appliance: person, vehicle and pet detection with a false-alarm rate below 3%, 100% local computation and no subscription.
Browse all platforms →An off-grid security camera with local storage records onto hardware at the site, powered by the site's own supply, with no cloud…
November 20, 2026A NAS backup strategy for business rests on three pillars in 2026: a copy that is separate from the primary array, a…
November 20, 2026A security camera system without monthly fees records to storage you own, on hardware that processes video locally, instead of uploading clips…
Ask our export team for the OEM/ODM cooperation guide and a written quotation.